White Rodgers 1F85-277 Guía para resolver problemas Pagina 41
- Pagina / 134
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
To view the setpoint temperature, press the or button
once. The
icon appears and the thermostat displays the
setpoint temperature. To change the setpoint, press the or
button to raise or lower the temperature until the desired
setpoint is reached.
To turn the backlight on, press the button, or the or
button once.
To change the thermostat installer configuration, press and
hold the
button for 5 seconds. The features and (defaults)
are selected by pressing the button once to scan the installer
configuration selections. The defaults are changed with the or
button. (Please refer to the following table for the selections
of your choice.)
Default Options
Backlight LO (On) LF (Off)
Display Reading Adjustment* H0.0 L3.0 to H3.0
Proportional Control** PO (On) PF (Off)
Anticipation***
AL(2000-4000 W) AS (500-2000 W)
Temperature Scale SC (Celsius) SF (Fahrenheit)
* Adjusts room temperature display higher or lower to agree
with a previous thermostat.
** Proportional Control allows the thermostat to modulate de-
pending on power usage.
***Adjusts your thermostat anticipation based on the room and
baseboard heater size, e.g., in a room with a 3500 W base-
board heater, set your thermostat anticipation to AL.
The thermostat will save the setpoint temperature and installer
configuration selections permanently, even after power out-
ages.
To reset the thermostat, press the
, , and buttons simul-
taneously.
To suspend the thermostat operation, slide the thermostat switch
to the position. In this position, the thermostat still has power
but the display is turned off.
WIRING AND
CONFIGURATION1E65-144
NOTE
Use with copper conductors only. Use wire con-
nectors approved for 12 AWG only.
Make the appropriate connections to the thermostat as per
diagram below. The wires are non-polarized so either wire can
be connected to either terminal.
2 Wire Installation
4 Wire Installation
Slide thermostat switch to position. The thermostat normally
displays the actual ambient temperature.
The thermostat displays the percentage of power usage (in
"PC" mode only) required to maintain the desired temperature.
For example:
100% power usage
70% power usage
30% power usage
www.white-rodgers.com
164
TECHNICAL HELP
- TECHNICAL HELPINDEX 1
- INDEXTECHNICAL HELP 2
- TYPICAL WIRING1F97-1277 3
- 1F97-1277CONFIGURATION 4
- 1F95-1280CONFIGURATION 6
- 1F95-1291CONFIGURATION 8
- Heat Pump Connections 9
- Heat Pump Systems 9
- 1F95-1277CONFIGURATION 10
- (limited temperature range) 10
- INSTALLER/CONFIGURATION MENU 10
- Remote Sensor Terminals 11
- 1F97-0671CONFIGURATION 12
- TYPICAL WIRING1F95EZ-0671 13
- 1F95EZ-0671 14
- AND CONFIGURATION 14
- TYPICAL WIRING1F95-0671 15
- AND CONFIGURATION 1F95-0671 16
- CONFIGURATION1F95-0671 17
- TYPICAL WIRING 1F95-0680 18
- AND CONFIGURATION1F95-0680 19
- AND CONFIGURATION 1F95-0680 20
- 1F80-0471/1F86-0471 21
- CONFIGURATION AND 21
- TERMINAL OUTPUTS 21
- TYPICAL WIRING DIAGRAMS 22
- 1F83-0471/1F85-0471 23
- CONFIGURATION 24
- 1F83-0422/1F85-0422 24
- * Common connection 25
- TYPICAL WIRING1F85-0477 27
- 1F85-0477 28
- CONFIGURATION1F85-0477 29
- 1F80-0224/1F86-0244 30
- 1F80-0261/1F87-0261 30
- TAPE OFF! 32
- CONFIGURATION MENU 33
- 1F82-261 / 1F89-211 35
- 1E78-151 37
- 1F72-151 38
- 1F79-111 38
- WIRING AND 41
- CONFIGURATION1E65-144 41
- 2 Wire Installation 41
- 4 Wire Installation 41
- Troubleshooting Chart 43
- To + or S1 44
- To S or S2 44
- To - or S3 44
- + Terminals 45
- - Terminals 45
- EVAPORATIVE 46
- HEATING TECH HELP INDEX 47
- MAIN VALVE RELAY 48
- TH PGTH-PG 48
- REDUNDANT PILOT/VALVE 50
- ELECTRICAL SCHEMATIC 51
- 36E WIRING 52
- INFORMATION 52
- FURNACE CONTROLS 55
- 21M51U-843 WIRING 55
- INTEGRATED 55
- OPTION SWITCHES 57
- HEAT MODE 57
- DIAGNOSTIC TABLE 59
- 21M51U-843 59
- 50V51-843 60
- 21V51U-843 65
- FAULT INDEX CHART 66
- 1E1D1C 1F 67
- 1I1H1G 1J 1K 67
- 50A55-843 72
- 50A62-820 75
- 50A65-843 78
- L2 must be grounded 81
- LED Condition 83
- 50D50-842 WIRING 85
- 50D50-843 WIRING 85
- SYSTEM LOCKOUT AND 88
- DIAGNOSTIC FEATURES 88
- FAULT RECALL 89
- FAULT CODE RESET 89
- SILENT OPERATOR CONTROL 90
- BOARD MOUNT 91
- LIMIT CONTROLS 91
- 3L09 OUTLINE 91
- Figure 4 92
- Figure 3 92
- Wiring Instruction Notes 94
- 16E09-101 95
- USER MENU 95
- USER MENU / OPERATION 96
- SPECIAL 97
- TRANSFORMERS AND RELAYS 99
- TECHNICAL HELP 100
- WIRING DIAGRAMS 8A04-1 101
- 8A04-1 Typical Wiring 101
- 1311 Three Wire Zone Valve 102
- 1361 Two Wire Zone Valve 103
- TECH HELP INDEX 104
- INDOOR AIR QUALITY / 104
- ZONING SYSTEMS 104
- SIZING AND OZONE 105
- WHAT AIR CLEANERS DO 106
- AND HOW THEY WORK 106
- PARTS VIEW DIAGRAM 107
- COMFORTPRO 109
- AIR CLEANERS 109
- PARTS LIST 109
- AIR CLEANER 110
- PROGRAMMING OPTIONS 110
- TYPICAL WIRING 112
- DIAGRAMS 112
- REPLACEMENT 113
- HFT2900FP 116
- ZONING SYSTEM DESIGN 117
- MINIMUM POSITION DAMPER 118
- ZONING HEAT PUMPS 118
- ZONING COMMERCIAL SYSTEMS 119
- ZONING versus MULTIPLE UNITS 119
- 78123456 121
- WIRING DIAGRAM 4 – 122
- OPERATION AND WIRING 123
- Leading Air Sensor 123
- CZ-4/CAZ-2 ADDING ZONES 124
- AND TROUBLESHOOTING 124
- INSTALLATION 125
- OPERATION 125
- ZONE PANEL 126
- LEAVING AIR SENSOR (CLAS) 127
- TROUBLESHOOTING 127
- CMM-3UKZONE PANEL 128
- CMM-3U WIRING DIAGRAM 132
- BAROMETRIC RELIEF DAMPERS 133
- LOCATION 133
- CRDS ROUND 134
- SPRING RETURN DAMPERS 134
Relacionado con productos y manuales para Acondicionadores de aire del sistema de división White Rodgers 1F85-277
(12 paginas)Empire Comfort Systems OLP42FP72S-2 manuals
Owner’s manuals and user’s guides for Fireplaces Empire Comfort Systems OLP42FP72S-2.
We providing 1 pdf manuals Empire Comfort Systems OLP42FP72S-2 for download free by document types: Owner's Manual
Comentarios a estos manuales